Victron MultiPlus Compact 12/2000/80-50 120V VE.Bus – Power Inverter/Charger

CMP122200100 Victron

Log in to see price!

Available on backorder

Victron MultiPlus Compact 12/2000/80-50 120V VE.Bus – Power Inverter/Charger
4000 Watt Inverter

With PowerControl & PowerAssist
Transfer switch: 50 amp
Parallel and 3-phase operation

• Inverter Mode: 9.5V – 17V DC
Output: 120V 60Hz
Continuous output power at 77 °F(VA): 2000
Continuous output power at 77 °F : 1600 Watt
Continuous output power at 100 °F : 1450 Watt
Continuous output power at 150 °F : 1100 Watt
Peak power : 4000 Watt
Maximum efficiency: 92%
Zero-load power : 9 Watt
Zero load power in AES mode : 7 Watt
Zero load power in Search mode : 3 Watt

• Charge Mode
Charge voltage (absorption) : 14.4V DC
Charge voltage (float) : 13.8V DC
Storage mode : 13.2V DC
Charge current house battery : 80 amps
Charge current starter battery : 4 amps
Battery temperature sensor

Unit Weight: 25 lbs
Unit Dimensions (H x W x D): 20.5″ x 10″ x 5″

Multifunctional, with intelligent power management
The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions, the MultiPlus has several advanced features, as outlined below.

Two AC Outputs
The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. The second output is live only when AC is available on one of the inputs of the MultiPlus. Loads that should not discharge the battery, like a water heater for example, can be connected to this output.

PowerControl – Dealing with limited generator, shore side or grid power
The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply. With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.

PowerAssist – Boosting the capacity of shore or generator power
This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Four stage adaptive charger and dual bank battery charging
The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery.

System configuring has never been easier
After installation, the MultiPlus is ready to go. If settings have to be changed, this can be done in a matter of minutes with a new DIP switch setting procedure. Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed! Alternatively, VE.Net can be used instead of the DIP switches. And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features

SKU CMP122200100
Manufacturer Model #
UPC
Case Quantity 1
Brand:
Weight 0.00 lbs
Carton Dimensions